Your Trusted B2B Sourcing Platform About | Help | Sign In | Post Request
Buying Guide

CNC Machining Cost Per Part Calculator: How to Build Accurate RFQ Estimates and Benchmark Chinese Supplier Quotes

Why a Cost-Per-Part Model Beats Guesswork

Most procurement teams evaluate CNC quotes by comparing three numbers side by side and picking the middle one. That approach fails for a simple reason: two suppliers can submit identical prices built on completely different cost structures—one may be underpricing setup to win the account, the other may be overcharging on material. Without a bottom-up model, you cannot tell which is which until the first production run goes wrong.

A cnc machining cost per part calculator solves this by decomposing every quote into its cost drivers: raw material, stock removal time, machine hourly rate, setup amortization, finishing, and margin. Once you can rebuild a supplier's number from first principles, you can spot bids that are 40% below the floor (a quality risk) or 30% above the ceiling (a negotiation opportunity). This guide walks through building that model, with worked examples for aluminum 6061 and 304 stainless steel, tolerance-to-cost multipliers, and a verification checklist you can apply to any Chinese supplier quote.

The stakes are real. Across our supplier directory, bracket-type parts in this category currently span an observed unit price range of roughly $2.80 to $12.00. That 4x spread is not explained by part complexity alone—it reflects differences in material sourcing, machine selection, and how suppliers allocate overhead. A structured calculator tells you where within that range a given part should land.

Aerial view of modern industrial factory with buildings and various special equipments in daytime (Photo: Tom Fisk / Pexels)

The Six Cost Drivers in Any CNC Quote

Every credible quote, whether from a Chinese job shop or a European contract manufacturer, is the sum of six components. Build your calculator around these, and the arithmetic stays manageable.

1. Raw Material Cost

Material is usually the largest single line item for aluminum parts and a significant one for stainless. Calculate it as blank volume × material density × price per kilogram, then add a scrap factor. For machined parts from bar or plate, a 15–25% material waste allowance is typical; for parts nested on plate, waste can run higher.

2. Stock Removal Time

This is where most home-built calculators go wrong. Machining time is not proportional to part weight—it is proportional to the volume of material removed divided by the material removal rate (MRR) for the chosen tool and material. Roughing aluminum 6061 on a 3-axis VMC with a 12 mm carbide end mill might achieve an MRR of 60–120 cm³/min; 304 stainless on the same machine might achieve 8–20 cm³/min. That 5–8x difference in removal rate is the single biggest reason stainless parts cost more than aluminum parts of identical geometry.

3. Machine Hourly Rate

Chinese suppliers typically quote internally at ¥80–¥250 per hour for 3-axis VMCs, ¥150–¥400 for 4-axis, and ¥300–¥800 for 5-axis or mill-turn equipment. Converted at current exchange rates, that is roughly $11–$35/hr for 3-axis work—well below Western rates of $60–$120/hr, which is the core of China's cost advantage. Use the rate appropriate to the machine the part actually requires, not the shop's cheapest rate.

4. Setup Amortization

Setup time (fixturing, tool loading, first-article checks, program prove-out) is a fixed cost per batch. A simple 3-axis part may need 0.5–1.5 hours of setup; a 5-axis part with tight tolerances may need 4–8 hours. Divide total setup cost by batch quantity to get the per-part contribution. This is why a 10-piece order can cost 3x per part what a 1,000-piece order costs.

5. Finishing and Secondary Operations

Anodizing, passivation, powder coating, deburring, and inspection add cost that is often quoted as a flat per-part or per-batch fee. Ask for these as separate line items—bundled finishing is a common place for margin to hide.

6. Margin and Overhead

Chinese job shops typically target 15–30% gross margin on export orders, with overhead (QA, packaging, export documentation, freight coordination) adding another 8–15%. If a quote's implied margin falls below 10%, either the supplier is buying the account or something in the cost build is understated—both are risks you should price in.

Worked Example: Aluminum 6061 Mounting Plate

Consider an aluminum rail mounting plate—a part type common in our directory—measuring 200 × 120 × 12 mm, with 6 through-holes, 2 tapped holes, and a ±0.1 mm general tolerance. Blank size 210 × 130 × 15 mm.

Cost ElementCalculationCost (USD)
Material0.41 kg blank × $3.20/kg × 1.2 scrap factor$1.57
Roughing time~110 cm³ removed ÷ 80 cm³/min ≈ 1.4 min—
Drilling + tapping8 holes, ~0.4 min each—
Total cycle time≈ 4.6 min at $18/hr$1.38
Setup amortization1.0 hr × $18 ÷ 500 pcs$0.04
Deburr + inspectionFlat per-part allowance$0.35
Anodize (clear)Per-part batch rate$0.60
Subtotal$3.94
Overhead + margin (25%)$0.99
Modeled unit price≈ $4.93

If a supplier quotes $3.20 for this part at 500 pieces, your model says they are either running faster than your assumed MRR (possible with high-speed toolpaths—ask), sourcing cheaper material (ask for the mill certificate), or compressing margin below sustainable levels. If they quote $9.00, you have a documented basis to negotiate.

Spacious industrial workshop featuring a crane and heavy machinery in Konya, Türkiye. (Photo: Cemrecan Yurtman / Pexels)

Worked Example: 304 Stainless Locking Bracket

Now take a heavy-duty steel locking bracket of similar envelope but in 304 stainless, with a ±0.05 mm tolerance on two mating features and a passivation finish.

Cost ElementCalculationCost (USD)
Material0.95 kg blank × $5.50/kg × 1.25 scrap$6.53
Roughing time~110 cm³ ÷ 14 cm³/min ≈ 7.9 min—
Finishing passes (tight tol.)+40% cycle time—
Total cycle time≈ 13 min at $22/hr$4.77
Setup amortization2.5 hr × $22 ÷ 300 pcs$0.18
Deburr + passivationPer-part allowance$1.10
Subtotal$12.58
Overhead + margin (25%)$3.15
Modeled unit price≈ $15.73

Note how the stainless part lands well above the observed $2.80–$12.00 range for this category while the aluminum part sits comfortably inside it. That is expected: the observed range reflects typical bracket geometry and materials, and a tight-tolerance stainless part with passivation legitimately exceeds it. The point of the calculator is not to force every quote into a range—it is to explain why a number sits where it does.

Tolerance-to-Cost Multipliers

Tolerance is the most underpriced variable in RFQ evaluation. As a rule of thumb, apply these multipliers to the machining-time component (not material) when moving from a baseline of ±0.1 mm general tolerance on a 3-axis part:

  • ±0.1 mm (general): 1.0x baseline
  • ±0.05 mm: 1.3–1.5x (finish passes, more inspection)
  • ±0.025 mm: 1.8–2.2x (may require 4-axis or CMM verification)
  • ±0.01 mm: 2.5–3.5x (grinding or jig-boring operations, climate-controlled inspection)
  • Geometric tolerances (flatness, perpendicularity) under 0.02 mm: add 20–40% on top of the size-tolerance multiplier

Surface finish follows a similar logic: Ra 3.2 µm is standard from milling; Ra 1.6 µm adds roughly 15–25%; Ra 0.8 µm or better typically requires additional finishing operations and can add 40% or more. When a supplier quotes a tight-tolerance part at general-tolerance pricing, ask to see their inspection plan—the gap usually shows up there.

Red Flags When Benchmarking Chinese Quotes

  • No breakdown provided. A supplier who will not separate material, machining, setup, and finishing is either hiding margin or has not costed the job properly. Either way, you cannot verify the number.
  • Price below your material cost floor. If the quoted price is under your calculated raw material cost plus 15%, the supplier is likely substituting material grade or planning to renegotiate after winning the order.
  • Identical pricing across radically different tolerances. A shop quoting the same rate for ±0.1 mm and ±0.02 mm parts is not inspecting to the tighter spec.
  • Setup charges that vanish at low quantities. Legitimate setup is a fixed cost; a quote that shows near-zero setup on a 20-piece order is absorbing it into unit price and will not scale.
  • No mill certificates or material traceability offered. For 304 stainless especially, grade substitution (201 or 304L passed off as 304) is a known risk.
  • Unwillingness to quote first article inspection (FAI) separately. FAI is a real cost; suppliers who bundle it free are either skipping it or padding elsewhere.

Questions to Ask Before Accepting a Quote

  1. Can you provide a cost breakdown by material, machining time, setup, and finishing?
  2. What machine will this part run on, and what is your hourly rate for that machine?
  3. What material removal rate did you assume for this material and geometry?
  4. What is your assumed scrap rate, and how is material waste handled on nested plate parts?
  5. Will you supply mill certificates with the shipment?
  6. What is your first article inspection process, and can I see a sample report?
  7. How do you handle tolerance stack-up on the critical features of this part?
  8. What is your typical on-time delivery rate for export orders in this category?
  9. If we double the order quantity, how much does the unit price drop, and why?
  10. What happens to pricing if material index prices move 10%?

Supplier Quote Verification Checklist

CheckPass Criteria
Quote includes line-item breakdownMaterial, machining, setup, finishing listed separately
Material cost within ±20% of your modelConsistent with current index pricing plus stated scrap factor
Machining time plausible for materialImplied MRR within published ranges for the alloy and tooling
Setup amortization scales with quantityPer-part setup falls as batch size rises
Tolerance pricing reflects multipliersTight features carry visible cost premium
Finishing quoted separatelyAnodize/passivation/coating as distinct line items
Inspection and FAI addressedReport sample available on request
Material traceability offeredMill certs included in shipment documentation
Margin implied by quote is sustainable15–30% gross margin band, not below 10%
Price movement clause definedMaterial index adjustment mechanism stated in writing

Using the Model in Negotiation

The calculator's real value emerges in the second round. When a supplier quotes $9.00 against your $4.93 model, you do not counter with a number—you counter with a question: "Our model assumes 4.6 minutes of cycle time at $18/hr and $0.60 for anodize. Which of those inputs differs in your cost build?" Suppliers respect buyers who understand cost structure, and the conversation usually surfaces either a legitimate difference (their machine is slower, their anodizer charges more) or room to move. The same logic protects you from the opposite error: accepting a $3.20 quote that looks like a bargain until the first batch arrives out of tolerance.

Start with the observed range in your category as a sanity band, build the bottom-up model for the specific part, and let the two inform each other. Where they diverge sharply, you have found either an opportunity or a risk—and either way, you now know which.

Frequently Asked Questions

How accurate is a cost-per-part calculator compared to actual supplier quotes?

A well-built model typically lands within 15–25% of a legitimate quote for standard 3-axis parts. The gap widens for complex 5-axis geometry or unusual materials, where supplier-specific factors like tooling inventory and programmer skill matter more. Use the model as a benchmark band, not a precise prediction—its purpose is to flag outliers, not to replace quoting.

Why do Chinese CNC quotes vary so widely for similar parts?

The spread reflects genuine differences in machine selection, material sourcing, batch-size assumptions, and margin strategy—not just quality. In our directory, bracket-type parts currently span roughly $2.80 to $12.00 per unit, and a bottom-up model can explain most of that variance for any specific part. Quotes at the extreme low end usually indicate compressed margin or understated inspection, while high-end quotes often reflect small-batch assumptions or premium finishing.

What tolerance should I specify to control cost without sacrificing function?

Specify the loosest tolerance that satisfies the part's function, and tighten only on features that mate or locate. Moving an entire drawing from ±0.1 mm to ±0.025 mm can add 80–120% to machining cost, while tightening only two critical features might add 15–25%. Mark critical features explicitly on the drawing so suppliers price them correctly rather than applying the tightest tolerance across the whole part.

Ready to source from verified suppliers? Get free quotes and compare offers within 24 hours.

Frequently Asked Questions

How accurate is a cost-per-part calculator compared to actual supplier quotes?

A well-built model typically lands within 15–25% of a legitimate quote for standard 3-axis parts. The gap widens for complex 5-axis geometry or unusual materials, where supplier-specific factors like tooling inventory and programmer skill matter more. Use the model as a benchmark band, not a precise prediction—its purpose is to flag outliers, not to replace quoting.

Why do Chinese CNC quotes vary so widely for similar parts?

The spread reflects genuine differences in machine selection, material sourcing, batch-size assumptions, and margin strategy—not just quality. In our directory, bracket-type parts currently span roughly $2.80 to $12.00 per unit, and a bottom-up model can explain most of that variance for any specific part. Quotes at the extreme low end usually indicate compressed margin or understated inspection, while high-end quotes often reflect small-batch assumptions or premium finishing.

What tolerance should I specify to control cost without sacrificing function?

Specify the loosest tolerance that satisfies the part's function, and tighten only on features that mate or locate. Moving an entire drawing from ±0.1 mm to ±0.025 mm can add 80–120% to machining cost, while tightening only two critical features might add 15–25%. Mark critical features explicitly on the drawing so suppliers price them correctly rather than applying the tightest tolerance across the whole part.

Ready to Get Your CNC Parts Made in China

Get matched with verified suppliers who can meet your exact specifications.

Get Free Quotes
基本 文件 流程 错误 SQL 调试
  1. 请求信息 : 2026-11-17 22:27:40 HTTP/2.0 GET : https://cnc-parts-china.com/guides/cnc-machining-cost-per-part-calculator-how-to-build-accurate-rfq-estimates-and-benchmark-chinese-supplier-quotes
  2. 运行时间 : 0.061603s [ 吞吐率:16.23req/s ] 内存消耗:5,233.38kb 文件加载:153
  3. 缓存信息 : 0 reads,0 writes
  4. 会话信息 : SESSION_ID=e624342df28f0cfde7497bdb58b90250
  1. /www/wwwroot/www.cnc-parts-china.com/public/index.php ( 0.79 KB )
  2. /www/wwwroot/www.cnc-parts-china.com/vendor/autoload.php ( 0.75 KB )
  3. /www/wwwroot/www.cnc-parts-china.com/vendor/composer/autoload_real.php ( 1.63 KB )
  4. /www/wwwroot/www.cnc-parts-china.com/vendor/composer/platform_check.php ( 0.90 KB )
  5. /www/wwwroot/www.cnc-parts-china.com/vendor/composer/ClassLoader.php ( 15.99 KB )
  6. /www/wwwroot/www.cnc-parts-china.com/vendor/composer/autoload_static.php ( 6.03 KB )
  7. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-helper/src/helper.php ( 8.34 KB )
  8. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-validate/src/helper.php ( 2.19 KB )
  9. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/helper.php ( 1.47 KB )
  10. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/stubs/load_stubs.php ( 0.16 KB )
  11. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Exception.php ( 1.69 KB )
  12. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-container/src/Facade.php ( 2.71 KB )
  13. /www/wwwroot/www.cnc-parts-china.com/vendor/ralouphie/getallheaders/src/getallheaders.php ( 1.60 KB )
  14. /www/wwwroot/www.cnc-parts-china.com/vendor/symfony/polyfill-mbstring/bootstrap.php ( 8.26 KB )
  15. /www/wwwroot/www.cnc-parts-china.com/vendor/symfony/polyfill-mbstring/bootstrap80.php ( 9.78 KB )
  16. /www/wwwroot/www.cnc-parts-china.com/vendor/symfony/var-dumper/Resources/functions/dump.php ( 0.99 KB )
  17. /www/wwwroot/www.cnc-parts-china.com/vendor/ezyang/htmlpurifier/library/HTMLPurifier.composer.php ( 0.10 KB )
  18. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-dumper/src/helper.php ( 0.18 KB )
  19. /www/wwwroot/www.cnc-parts-china.com/vendor/symfony/var-dumper/VarDumper.php ( 3.73 KB )
  20. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/App.php ( 15.30 KB )
  21. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-container/src/Container.php ( 15.76 KB )
  22. /www/wwwroot/www.cnc-parts-china.com/vendor/psr/container/src/ContainerInterface.php ( 1.02 KB )
  23. /www/wwwroot/www.cnc-parts-china.com/app/provider.php ( 0.19 KB )
  24. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Http.php ( 6.22 KB )
  25. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-helper/src/helper/Str.php ( 7.29 KB )
  26. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Env.php ( 4.68 KB )
  27. /www/wwwroot/www.cnc-parts-china.com/app/common.php ( 0.90 KB )
  28. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/helper.php ( 18.77 KB )
  29. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Config.php ( 5.93 KB )
  30. /www/wwwroot/www.cnc-parts-china.com/config/app.php ( 0.95 KB )
  31. /www/wwwroot/www.cnc-parts-china.com/config/cache.php ( 0.78 KB )
  32. /www/wwwroot/www.cnc-parts-china.com/config/console.php ( 1.07 KB )
  33. /www/wwwroot/www.cnc-parts-china.com/config/cookie.php ( 0.56 KB )
  34. /www/wwwroot/www.cnc-parts-china.com/config/database.php ( 2.13 KB )
  35. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/facade/Env.php ( 1.67 KB )
  36. /www/wwwroot/www.cnc-parts-china.com/config/filesystem.php ( 0.61 KB )
  37. /www/wwwroot/www.cnc-parts-china.com/config/lang.php ( 0.91 KB )
  38. /www/wwwroot/www.cnc-parts-china.com/config/log.php ( 1.35 KB )
  39. /www/wwwroot/www.cnc-parts-china.com/config/middleware.php ( 0.19 KB )
  40. /www/wwwroot/www.cnc-parts-china.com/config/route.php ( 2.27 KB )
  41. /www/wwwroot/www.cnc-parts-china.com/config/session.php ( 0.69 KB )
  42. /www/wwwroot/www.cnc-parts-china.com/config/trace.php ( 0.34 KB )
  43. /www/wwwroot/www.cnc-parts-china.com/config/view.php ( 0.82 KB )
  44. /www/wwwroot/www.cnc-parts-china.com/app/event.php ( 0.25 KB )
  45. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Event.php ( 7.77 KB )
  46. /www/wwwroot/www.cnc-parts-china.com/app/service.php ( 0.13 KB )
  47. /www/wwwroot/www.cnc-parts-china.com/app/AppService.php ( 0.26 KB )
  48. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Service.php ( 1.64 KB )
  49. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Lang.php ( 7.35 KB )
  50. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/lang/zh-cn.php ( 13.70 KB )
  51. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/initializer/Error.php ( 3.31 KB )
  52. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/initializer/RegisterService.php ( 1.33 KB )
  53. /www/wwwroot/www.cnc-parts-china.com/vendor/services.php ( 0.15 KB )
  54. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/service/PaginatorService.php ( 1.52 KB )
  55. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/service/ValidateService.php ( 0.99 KB )
  56. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/service/ModelService.php ( 2.04 KB )
  57. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-trace/src/Service.php ( 0.77 KB )
  58. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Middleware.php ( 6.72 KB )
  59. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/initializer/BootService.php ( 0.77 KB )
  60. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/Paginator.php ( 11.86 KB )
  61. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-validate/src/Validate.php ( 63.20 KB )
  62. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/Model.php ( 23.55 KB )
  63. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-helper/src/contract/Arrayable.php ( 0.09 KB )
  64. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-helper/src/contract/Jsonable.php ( 0.13 KB )
  65. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/model/contract/Modelable.php ( 0.09 KB )
  66. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/model/concern/Attribute.php ( 21.05 KB )
  67. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/model/concern/AutoWriteData.php ( 4.20 KB )
  68. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/model/concern/Conversion.php ( 6.75 KB )
  69. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/model/concern/DbConnect.php ( 5.16 KB )
  70. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/model/concern/ModelEvent.php ( 2.33 KB )
  71. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/model/concern/RelationShip.php ( 28.30 KB )
  72. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Db.php ( 2.88 KB )
  73. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/DbManager.php ( 8.52 KB )
  74. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Log.php ( 6.28 KB )
  75. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Manager.php ( 3.92 KB )
  76. /www/wwwroot/www.cnc-parts-china.com/vendor/psr/log/src/LoggerInterface.php ( 2.71 KB )
  77. /www/wwwroot/www.cnc-parts-china.com/vendor/psr/log/src/LoggerTrait.php ( 2.69 KB )
  78. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Cache.php ( 4.92 KB )
  79. /www/wwwroot/www.cnc-parts-china.com/vendor/psr/simple-cache/src/CacheInterface.php ( 4.71 KB )
  80. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-helper/src/helper/Arr.php ( 17.45 KB )
  81. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/cache/driver/File.php ( 7.84 KB )
  82. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/cache/Driver.php ( 9.02 KB )
  83. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/contract/CacheHandlerInterface.php ( 1.99 KB )
  84. /www/wwwroot/www.cnc-parts-china.com/app/Request.php ( 0.09 KB )
  85. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Request.php ( 54.64 KB )
  86. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/traits/UrlHandler.php ( 6.05 KB )
  87. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/traits/DomainHandler.php ( 5.49 KB )
  88. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/traits/HttpMethodHandler.php ( 4.74 KB )
  89. /www/wwwroot/www.cnc-parts-china.com/app/middleware.php ( 0.30 KB )
  90. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Pipeline.php ( 2.61 KB )
  91. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-trace/src/TraceDebug.php ( 3.40 KB )
  92. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/middleware/SessionInit.php ( 1.94 KB )
  93. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Session.php ( 1.80 KB )
  94. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/session/driver/File.php ( 6.27 KB )
  95. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/contract/SessionHandlerInterface.php ( 0.87 KB )
  96. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/session/Store.php ( 7.12 KB )
  97. /www/wwwroot/www.cnc-parts-china.com/app/middleware/InstallCheck.php ( 0.82 KB )
  98. /www/wwwroot/www.cnc-parts-china.com/app/middleware/Maintenance.php ( 1.64 KB )
  99. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/facade/Db.php ( 0.93 KB )
  100. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/connector/Mysql.php ( 5.73 KB )
  101. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/PDOConnection.php ( 53.74 KB )
  102. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/Connection.php ( 8.39 KB )
  103. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/ConnectionInterface.php ( 4.57 KB )
  104. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/builder/Mysql.php ( 16.58 KB )
  105. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/Builder.php ( 24.07 KB )
  106. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/BaseBuilder.php ( 27.50 KB )
  107. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/Query.php ( 15.97 KB )
  108. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/BaseQuery.php ( 45.13 KB )
  109. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/concern/TimeFieldQuery.php ( 7.43 KB )
  110. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/concern/AggregateQuery.php ( 3.26 KB )
  111. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/concern/ModelRelationQuery.php ( 20.07 KB )
  112. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/concern/ParamsBind.php ( 3.66 KB )
  113. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/concern/ResultOperation.php ( 7.01 KB )
  114. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/concern/WhereQuery.php ( 19.37 KB )
  115. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/concern/JoinAndViewQuery.php ( 7.11 KB )
  116. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/concern/TableFieldInfo.php ( 2.63 KB )
  117. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/concern/Transaction.php ( 2.77 KB )
  118. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/log/driver/File.php ( 6.10 KB )
  119. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/contract/LogHandlerInterface.php ( 0.86 KB )
  120. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/log/Channel.php ( 3.89 KB )
  121. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/event/LogRecord.php ( 1.02 KB )
  122. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Route.php ( 23.73 KB )
  123. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/route/RuleName.php ( 5.74 KB )
  124. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/route/Domain.php ( 2.53 KB )
  125. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/route/RuleGroup.php ( 22.41 KB )
  126. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/route/Rule.php ( 27.49 KB )
  127. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/route/RuleItem.php ( 9.78 KB )
  128. /www/wwwroot/www.cnc-parts-china.com/route/admin.php ( 11.49 KB )
  129. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/facade/Route.php ( 4.70 KB )
  130. /www/wwwroot/www.cnc-parts-china.com/route/app.php ( 3.73 KB )
  131. /www/wwwroot/www.cnc-parts-china.com/route/install.php ( 0.59 KB )
  132. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/route/dispatch/Controller.php ( 4.74 KB )
  133. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/route/Dispatch.php ( 11.32 KB )
  134. /www/wwwroot/www.cnc-parts-china.com/app/controller/content/Guide.php ( 1.71 KB )
  135. /www/wwwroot/www.cnc-parts-china.com/app/controller/front/BaseFrontController.php ( 70.19 KB )
  136. /www/wwwroot/www.cnc-parts-china.com/app/BaseController.php ( 6.06 KB )
  137. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/facade/View.php ( 1.70 KB )
  138. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/facade/Config.php ( 1.37 KB )
  139. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/View.php ( 4.39 KB )
  140. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/facade/Session.php ( 1.79 KB )
  141. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-helper/src/Collection.php ( 16.47 KB )
  142. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/Express.php ( 1.53 KB )
  143. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-orm/src/db/Raw.php ( 1.30 KB )
  144. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Response.php ( 9.07 KB )
  145. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/response/View.php ( 3.29 KB )
  146. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/Cookie.php ( 6.06 KB )
  147. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-view/src/Think.php ( 8.38 KB )
  148. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/framework/src/think/contract/TemplateHandlerInterface.php ( 1.60 KB )
  149. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-template/src/Template.php ( 46.61 KB )
  150. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-template/src/template/driver/File.php ( 2.41 KB )
  151. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-template/src/template/contract/DriverInterface.php ( 0.86 KB )
  152. /www/wwwroot/www.cnc-parts-china.com/runtime/temp/7ca10c289ae36b7629e662dcf2e3aff0.php ( 14.04 KB )
  153. /www/wwwroot/www.cnc-parts-china.com/vendor/topthink/think-trace/src/Html.php ( 4.42 KB )
  1. CONNECT:[ UseTime:0.000574s ] mysql:host=127.0.0.1;port=3306;dbname=cncpartsch;charset=utf8mb4
  2. SHOW FULL COLUMNS FROM `kt_system_config` [ RunTime:0.001229s ]
  3. SELECT `config_value` FROM `kt_system_config` WHERE `config_key` = 'maintenance_mode' LIMIT 1 [ RunTime:0.000420s ]
  4. SHOW TABLES LIKE 'kt_site' [ RunTime:0.001354s ]
  5. SHOW FULL COLUMNS FROM `kt_site` [ RunTime:0.001459s ]
  6. SELECT `favicon` FROM `kt_site` ORDER BY `id` ASC LIMIT 1 [ RunTime:0.000502s ]
  7. SHOW TABLES LIKE 'kt_system_config' [ RunTime:0.000841s ]
  8. SELECT `config_value` FROM `kt_system_config` WHERE `config_key` = 'site_favicon' LIMIT 1 [ RunTime:0.000307s ]
  9. SELECT `logo` FROM `kt_site` ORDER BY `id` ASC LIMIT 1 [ RunTime:0.000337s ]
  10. SELECT `config_value` FROM `kt_system_config` WHERE `config_key` = 'site_logo' LIMIT 1 [ RunTime:0.000211s ]
  11. SELECT `name` FROM `kt_site` ORDER BY `id` ASC LIMIT 1 [ RunTime:0.000178s ]
  12. SELECT * FROM `kt_site` ORDER BY `id` ASC LIMIT 1 [ RunTime:0.000274s ]
  13. SELECT `config_value`,`config_key` FROM `kt_system_config` WHERE `config_key` IN ('site_name','site_domain','site_subtitle','site_description','site_logo','site_favicon','site_keywords','seo_home_title','seo_home_description','seo_home_keywords','contact_phone','contact_wechat','icp_code') [ RunTime:0.000331s ]
  14. SHOW FULL COLUMNS FROM `kt_category` [ RunTime:0.001185s ]
  15. SHOW COLUMNS FROM `kt_category` [ RunTime:0.000956s ]
  16. SELECT * FROM `kt_category` WHERE `parent_id` = 0 AND `site_id` = 1 AND `status` = 1 ORDER BY `sort` DESC,`id` ASC LIMIT 5 [ RunTime:0.000549s ]
  17. SHOW FULL COLUMNS FROM `kt_news` [ RunTime:0.001191s ]
  18. SELECT * FROM `kt_news` WHERE `site_id` = 1 AND `slug` = 'cnc-machining-cost-per-part-calculator-how-to-build-accurate-rfq-estimates-and-benchmark-chinese-supplier-quotes' AND `content_type` = 'buying_guide' AND `publish_status` = 'published' LIMIT 1 [ RunTime:0.000480s ]
  19. UPDATE `kt_news` SET `views` = `views` + 1 WHERE `id` = 377 [ RunTime:0.001862s ]
  20. SHOW FULL COLUMNS FROM `kt_news_data` [ RunTime:0.001105s ]
  21. SELECT * FROM `kt_news_data` WHERE `news_id` = 377 LIMIT 1 [ RunTime:0.000420s ]
  22. SELECT * FROM `kt_news` WHERE `site_id` = 1 AND `publish_status` = 'published' AND `category_id` = 80 AND `id` <> 377 AND `content_type` IN ('article','buying_guide','comparison','case_study') ORDER BY content_type = 'buying_guide' DESC,`id` DESC LIMIT 8 [ RunTime:0.001202s ]
0.068860s